Whether you are working on a DIY craft project or you need to clear a clog in your drain line, you may one day find yourself staring at PVC pipes and fittings, wondering how to separate them. If your threaded PVC pipes and fittings were not glued together with solvent cement, or if the solvent cement has not yet cured, you may be able to separate your PVC fairly easily. Unfortunately, once solvent cement has been applied and allowed to cure, separating your threaded PVC pipes and fittings can be more challenging, though not impossible. Before you break out the hacksaw, though, there are some alternatives that may do the trick.
Can Threaded PVC be Easily Separated?
Threaded PVC pipes, fittings, and joints are designed to create a tight seal when connected. This makes it much more challenging to separate two pieces of the pipe. There are two instances, though, where separating threaded PVC fittings and joints can be done fairly easily. One situation is if glue hasn’t been used to attach the threaded PVC. You may also be able to twist and pull PVC and fittings apart if the solvent cement used to glue them together has not yet cured. It is possible that the cement was not properly applied, which can also allow for loosening.
If Glue Wasn’t Used
Threaded PVC joints and fittings can often create a fairly tight seal simply by twisting the two together. For this reason, in many non-pressurized applications, primer and solvent cement may not have been used to connect the PVC. If you are trying to separate threaded PVC pipes and fittings that have not been glued together with solvent cement, it may be possible to simply twist the two pieces apart.
If you cannot loosen the pipe by twisting with your hands, you can try using a pipe wrench. Select a wrench that can be adjusted to the diameter of the pipe. Place the wrench on the threaded PVC pipe fitting and make sure the teeth of the wrench are firmly set, then turn the wrench counterclockwise. You can also try a lubricating product like WD-40. Apply it to the area around the threaded fitting or joint and wait a few minutes for the product to make its way into the connection. Then use the pipe wrench or your hands to twist the pipe counterclockwise until it is loose enough to remove.
If Glue Hasn’t Cured
It can be a terrible feeling to notice a mistake right after your threaded PVC pipes and fittings have been attached, but it’s not a lost cause yet. Fortunately, you will have a short time (about two minutes) to separate the threaded PVC before the solvent cement cures. Quickly twist and pull the pipe fitting or joint until it loosens. You can use your hands or the pipe wrench if extra traction is needed. In the event you aren’t able to loosen the threaded PVC pipe before the solvent cement cures, consider proceeding to one of the solutions below.
How to Separate Threaded PVC Pipes and Fittings that have been Glued
Heat the Joint
When solvent cement is applied to PVC pipe and fittings, it actually causes a chemical reaction that melts the two pieces together. In some situations, you may be able to soften that tight joint again by mimicking the chemical reaction with heat. Try using a hair dryer or blow torch to gently heat the area where the glue was applied. You can then twist and pull until the pipe is loosened. It’s important to note, however, that pipe that is loosened in this way should not be used again in pressurized or building applications. For crafting and DIY projects, it may be possible to reuse the threaded PVC fittings and joints. Also note, it is very important to heat the connection slowly.
Add More Glue
It seems counterproductive, but sometimes adding more glue to the joint can actually help to loosen threaded PVC fittings and joints. Because the glue—PVC solvent cement—temporarily melts the pipe, it may be able to soften the pipe, making it easier to twist or pull the pieces apart.
First, apply the primer over the glued area, including couplings and joints, and let it dry. After a few minutes, apply a thin layer of solvent cement on top of the primer. Remember that you’ll only have a couple of minutes before the glue is cured, so quickly twist and pull the pipe until the two pieces are separated.
It's important to note as well, that this method will only work on a very fresh joint.
Cut the Pipe
If the threaded PVC fittings and joints cannot be twisted or pulled off the pipe using one of the above methods, you’ll likely need to cut the joint. A hacksaw will be needed to cut through the strong PVC. Before you start cutting, though, locate the mistake and determine what you’ll need to fully repair the line of pipe. Be sure to have the correct couplings, fittings, joints, and PVC on hand to make the repair afterward. Then cut away the problem area and attach the new threaded PVC and fittings. The idea of cutting PVC pipe can seem intimidating, however. If this solution seems to be above your skill set, consider calling a plumber to remove and repair the PVC pipes and fittings.
Separating Threaded PVC Pipes and Fittings
Threaded PVC fittings and joints were designed to be durable and create tight seals. That’s why we rely on them for a variety of applications, from drain lines in our plumbing systems to materials for our crafting and DIY projects. If you find you need to separate or remove threaded PVC fittings or joints, it can be possible, but it could take some strength and precision.
In projects where solvent cement has not been used or has not dried, you may be able to twist and pull the threaded fittings with your hands or a pipe wrench. WD-40 or another lubricating product may also help to loosen your fittings. When solvent cement has cured, however, it will take more than twisting and pulling. You may be able to use heat or additional solvent cement to loosen the joint, or a hacksaw to cut the problem area out. When in doubt, contact a licensed plumber to assist you.
